November 23, 2019 Olivier - putting in service after finding in incomplete state. XYCB0 positions are placeholder. Nov. 25, 2019 Reference: ISK4214D-R99.dwg, with sequence starting at coords [inch]: x = 53.9771" y = 401.5641" Further note - x,y in the above context denotes the coordinates on the technical drawing. Do note that in IMS, the x/y optical convention is flipped. Olivier - sequence ends on ISK04214d-R99.dwg at coords [inch]: x = 32.525" y = 389.1353" REFERENCES Design drawings: ISK4214D-revI ISK4219D-rev5 November 23, 2019 Olivier - I'm putting these in a serviceable state after finding them with much missing information/irregular formatting. Believe M. Stewart and T. Planche authored previous/initial versions. Putting in service following discussion with FA. NOTE - XYCB5 positions are placeholder. reference drawing ISK4214D-R99.dwg with sequence start at coords [inch]: x = 32.5250" y = 389.1353" which is also the end of sequence itw_tm2.xml ITW COLLIMATORS SET TO 1" APERTURE DIAMETER, VERIFY. Olivier - sequence ends at ITW:IV5 centerpoint on ISK4214D-R99.dwg at coords [inch]: x = -42.2207" y = 345.6795" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify these numbers. Reference drawing ISK4214D-R99.dwg with sequence starting at coords [inch]: x = -42.2207" y = 345.6795" which is also the end of sequence itw_exit. Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = -67.0175" y = 305.7853" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify all distances/positions and add reference drawings. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = -67.1075" y = 305.7853" which is also the end of sequence ims_mb1.xml. November 23, 2019 Olivier - putting this into service, found this in an incomplete state. need to verify all distances. IMS:YCB8 and M8 positions placeholder. YSLIT10A and YCB10 also placeholder. end of sequence also is placeholder. verify IMS:MB2 parameters. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = -67.0441" y = 105.6724" which is also the end of sequence ims_db0.xml NOTE - IMS:RPM14 position is placeholder, device not on drawing. Olivier - sequence ends on drawing ISK4214D-R99.dwg at coords [inch]: x = 90.2426" y = 40.0662" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - putting into service, found in incomplete state. need to verify all parameters, starts/ends of sequences, etc. also check polarities. XYCB18 are placeholder. ATT18 too. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = 90.2426" y = 40.0662" which is also the end of sequence ims_db6.xml Olivier - sequence ends on ISK4241D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - found in incomplete state, putting into service. slit dimensions are temporary. check all dims and devices and positions. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" which is also the end of sequence ims_db15.xml Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = 263.6833" y = 82.0097" Olivier: Using reference drawing ISK4403D.DWG, April 4 2019. First pass aimed at verifying CSB:Q12->CSB:RPM14 for Tomography testing. Set reference start coordinate at point: X = 84.0398" Y = 108.0727" ELEMENT LENGTHS AND APERTURES HAVE BEEN VERIFIED - April 4 2019 Olivier: all CSB specific elements which don't translate to TRANSOPTR have been given 0 length and set at s=3000.0mm Olivier: Oct 22, 2019 Added marker IGun_output at location 111.19mm before CSB:RPM12 twiss parameters (IGUN): alpha = -4.3786 beta = 9.5699 mm/rad gamma = 2.109e-2 rad/mm e_rms = 1.4163e2 um (mm*mrad) current = 1.3568e-4 A desired_species = 16O5+ E = 11.271 keV Olivier: XCB13/YCB13 placed in sapce between Q13 and Q14 for TRANSOPTR (no x/y steerers) - this prevents negative drifts due to Q13 overlap. note: Q13 s = 3825.6291*mm Olivier Oct 22 2019 set to new subroutine slit, using placeholder 1mm by 1cm slit diameters for x and y (inverted-downstairs). Check this value. Olivier: CSB:MB14 arclength is 22.3367" = 567.3522mm NOTE Oct 22 2019 I've copied in the optr tag from IOS:MB (ios_db1.xml), set theta to 90deg, left ip=2 as it was originally in this (csb) file. I've asked Joseph Adegun to get the k1 parameters, edge angles and BI relationship, as he needs these simulations. Note - all values other than theta, ip are from IOS:MB NOTE Oct 30 2019 I've found the values after Rick produced them. CSB dipole is a 90deg magnet with a radius of curvature: rho" = 14.2214" rho(cm) = 36.1224cm for a 90deg bend, the element length is l = r*theta = pi*(90/180)*36.1224cm l = 567.409cm Olivier: CSB:B15, standard ISAC-45deg bender, arclength: 7.854" = 199.4916mm This sequence ends here so that in the future if tuneX or another app monitors conflicting beam paths, a ctis path can end at FC16 at the same time as a ite/itw path goes through to the yield station. Otherwise there would be a conflict, much like the way the controls beampaths are done. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 7203.0088 mm y = 6504.7495 mm As measured using e drawings pro on spencer's laptop. This should be the downstream edge of FC16A.