November 23, 2019 Olivier - putting in service after finding in incomplete state. XYCB0 positions are placeholder. Nov. 25, 2019 Reference: ISK4214D-R99.dwg, with sequence starting at coords [inch]: x = 53.9771" y = 401.5641" Further note - x,y in the above context denotes the coordinates on the technical drawing. Do note that in IMS, the x/y optical convention is flipped. Olivier - sequence ends on ISK04214d-R99.dwg at coords [inch]: x = 32.525" y = 389.1353" REFERENCES Design drawings: ISK4214D-revI ISK4219D-rev5 November 23, 2019 Olivier - I'm putting these in a serviceable state after finding them with much missing information/irregular formatting. Believe M. Stewart and T. Planche authored previous/initial versions. Putting in service following discussion with FA. NOTE - XYCB5 positions are placeholder. reference drawing ISK4214D-R99.dwg with sequence start at coords [inch]: x = 32.5250" y = 389.1353" which is also the end of sequence itw_tm2.xml ITW COLLIMATORS SET TO 1" APERTURE DIAMETER, VERIFY. Olivier - sequence ends at ITW:IV5 centerpoint on ISK4214D-R99.dwg at coords [inch]: x = -42.2207" y = 345.6795" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify these numbers. Reference drawing ISK4214D-R99.dwg with sequence starting at coords [inch]: x = -42.2207" y = 345.6795" which is also the end of sequence itw_exit. Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = -67.0175" y = 305.7853" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify all distances/positions and add reference drawings. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = -67.1075" y = 305.7853" which is also the end of sequence ims_mb1.xml. November 23, 2019 Olivier - putting this into service, found this in an incomplete state. need to verify all distances. IMS:YCB8 and M8 positions placeholder. YSLIT10A and YCB10 also placeholder. end of sequence also is placeholder. verify IMS:MB2 parameters. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = -67.0441" y = 105.6724" which is also the end of sequence ims_db0.xml NOTE - IMS:RPM14 position is placeholder, device not on drawing. Olivier - sequence ends on drawing ISK4214D-R99.dwg at coords [inch]: x = 90.2426" y = 40.0662" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - putting into service, found in incomplete state. need to verify all parameters, starts/ends of sequences, etc. also check polarities. XYCB18 are placeholder. ATT18 too. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = 90.2426" y = 40.0662" which is also the end of sequence ims_db6.xml Olivier - sequence ends on ISK4241D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - found in incomplete state, putting into service. slit dimensions are temporary. check all dims and devices and positions. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" which is also the end of sequence ims_db15.xml Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = 263.6833" y = 82.0097" Olivier: Using reference drawing ISK4403D.DWG, April 4 2019. First pass aimed at verifying CSB:Q12->CSB:RPM14 for Tomography testing. Set reference start coordinate at point: X = 84.0398" Y = 108.0727" ELEMENT LENGTHS AND APERTURES HAVE BEEN VERIFIED - April 4 2019 Olivier: all CSB specific elements which don't translate to TRANSOPTR have been given 0 length and set at s=3000.0mm Olivier: Oct 22, 2019 Added marker IGun_output at location 111.19mm before CSB:RPM12 twiss parameters (IGUN): alpha = -4.3786 beta = 9.5699 mm/rad gamma = 2.109e-2 rad/mm e_rms = 1.4163e2 um (mm*mrad) current = 1.3568e-4 A desired_species = 16O5+ E = 11.271 keV Olivier: XCB13/YCB13 placed in sapce between Q13 and Q14 for TRANSOPTR (no x/y steerers) - this prevents negative drifts due to Q13 overlap. note: Q13 s = 3825.6291*mm Olivier Oct 22 2019 set to new subroutine slit, using placeholder 1mm by 1cm slit diameters for x and y (inverted-downstairs). Check this value. Olivier: CSB:MB14 arclength is 22.3367" = 567.3522mm NOTE Oct 22 2019 I've copied in the optr tag from IOS:MB (ios_db1.xml), set theta to 90deg, left ip=2 as it was originally in this (csb) file. I've asked Joseph Adegun to get the k1 parameters, edge angles and BI relationship, as he needs these simulations. Note - all values other than theta, ip are from IOS:MB NOTE Oct 30 2019 I've found the values after Rick produced them. CSB dipole is a 90deg magnet with a radius of curvature: rho" = 14.2214" rho(cm) = 36.1224cm for a 90deg bend, the element length is l = r*theta = pi*(90/180)*36.1224cm l = 567.409cm Olivier: CSB:B15, standard ISAC-45deg bender, arclength: 7.854" = 199.4916mm This sequence ends here so that in the future if tuneX or another app monitors conflicting beam paths, a ctis path can end at FC16 at the same time as a ite/itw path goes through to the yield station. Otherwise there would be a conflict, much like the way the controls beampaths are done. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 7203.0088 mm y = 6504.7495 mm As measured using e drawings pro on spencer's laptop. This should be the downstream edge of FC16A. Spencer: sequence starts on ISK4403D.DWG at coordinates: x = 7203.0088 mm y = 6504.7495 mm As measured using e drawings pro on spencer's laptop. This should be the downstream edge of FC16A. only 's' was adjusted after moving over from sequence csb_db5, so lengths/apertures should still be verified as Olivier had done. ELEMENT LENGTHS AND APERTURES HAVE BEEN VERIFIED - April 4 2019 Olivier: CSB:VB20, ISAC-36deg bender, arclength = 6.2782" = 159.4663mm Olivier: Oct 22 2019 CHECK WHAT KIND OF ELEMENT THIS IS - I've set it to ecb so it shuts up, but think it's a 45 spherical Spencer 20200114 - XCB7 is a 9 degree bender. I am updating it to type 'defly'. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 6286.6455 mm y = 7426.2544 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of XCB7. Spencer: sequence starts on ISK4210D.DWG at coordinates: x = 5399.8853 mm y = 3714.7334 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of XCB7. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 5405.5801 mm y = 5956.6294 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q12. Spencer: sequence starts on ISK4403D.DWG at coordinates: x = 5405.5801 mm y = 5956.6294 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q12. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 5399.5708 mm y = 9935.0566 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q20. all s measurements were made from ISK4210D -meagan Olivier: Jan 31 2019, compared some distances to ISK4209d.dwg found several discrepancies. Unclear where some of these were referenced from. Quadrupole optr tags and polarity have been obtained from above source. Update - Feb 14 2019: Quadrupole polarities in ILT seem to have originally been coded in reverse. Polarities have been re-verified against both isk4209d.dwg and Rick's original ilt-ira optr tune at lin12.triumf.ca/optr/ISAC/RFQ_buncher/sy.f Prebuncher remains to be modelled in opera-2D. Remains unclear how to elegantly transition TRANSOPTR from DC to bunched. Will have to get guidance from Rick. For now, I've implemented a triple discrete RFGAP call for the prebuncher. This is useful for longitudinal bunching, however it's unclear if this will do a good job simulating the actual prebuncher. Start of sequence on ISK4209d.dwg is at position [inches] x = 291.109" y = -214.168" Spencer: End of sequence on ISK4209d.dwg is at position [inches] x = 277.9285" y = 207.6593" this is 1.8" downstream of the centre of ILT:Q42. Corresponds to position on ARIEL drawing ART2080.dwg of: x = 1839813.25 mm y = 2189703 mm Note that the units on ART2080.dwg appear to be messed up. To get an actual distance in mm the units given on drawing need to be divided by 25.4. Olivier: Jan 31 2019, compared some distances to ISK4209d.dwg found several discrepancies. Unclear where some of these were referenced from. Quadrupole optr tags and polarity have been obtained from above source. Update - Feb 14 2019: Quadrupole polarities in ILT seem to have originally been coded in reverse. Polarities have been re-verified against both isk4209d.dwg and Rick's original ilt-ira optr tune at lin12.triumf.ca/optr/ISAC/RFQ_buncher/sy.f Spencer: Start of sequence on ISK4209d.dwg is at position [inches] x = 277.9285" y = 207.6593" this is 1.8" downstream of the centre of ILT:Q42 (at the skimmer). Spencer: Sequence ends at upstream edge of the skimmer upstream of ILT:Q47. Coordinates of that on ISK4209d.dwg are (measured using e drawings PRO): x = 7831.4155 mm y = 4502.5396 mm Equivalent coordinates of that on ART2080.dwg are (measured using e drawings PRO): X: 1820204.125 mm Y: 2209312.0 mm Note that the units on this drawing (ART2080.dwg) appear to be messed up. To get an actual distance in mm the units given on drawing need to be divided by 25.4. Olivier: Jan 31 2019, compared some distances to ISK4209d.dwg found several discrepancies. Unclear where some of these were referenced from. Quadrupole optr tags and polarity have been obtained from above source. Update - Feb 14 2019: Quadrupole polarities in ILT seem to have originally been coded in reverse. Polarities have been re-verified against both isk4209d.dwg and Rick's original ilt-ira optr tune at lin12.tri umf.ca/optr/ISAC/RFQ_buncher/sy.f Spencer: Sequence starts at upstream edge of the skimmer upstream of ILT:Q47. Coordinates of that on ISK4209d.dwg are (measured using e drawings PRO): x = 7831.4155 mm y = 4502.5396 mm Equivalent coordinates of that on ART2080.dwg are (measured using e drawings PRO): X: 1820204.125 mm Y: 2209312.0 mm Note that the units on this drawing (ART2080.dwg) appear to be messed up. To get an actual distance in mm the units given on drawing need to be divided by 25.4. Olivier: placeholder booster position. Booster originally in /acc at s = 5500.00*mm, though likely placeholder. Moved back a bit to avoid negative drifts. POSITION STILL NEEDS TO BE CONFIRMED all EPICS PV's need to be verified for name **************************OLD****************************** Olivier: IRA:Q4 centerpoint is to be used for alignment of RFQ vane mapping. RFQ 2term field map original length = 760.1275cm, which starts at the beginning of the radial matching section. From Larry Root's bnd_rms4.f Relax3D simulation for the RMS, quotes distance of 6 reference cell length (first cell) to start of RMS, equal to 5.3250522cm. From drawings ISK0141D.dwg, ILE0195D.DWG, end point of IRA:Q4 coincides with beginning of RFQ tank vacuum point. Thus, add dS = 10*5.53250522mm + 0.5*1.0*25.4 (half of IRA:Q4 length), for dS = 68.0250522mm from midpoint of IRA:Q4 to start of RFQ vane/RMS. drift distance from middle of IRA:Q4 to RFQ map centerpoint: S_RFQ = S_Q4 + 0.5*25.4+1" + 10*5.53250522 + 0.5*10*760.1275 S_RFQ = S_Q4 + 3868.6626mm Note that this is a single data point, from Larry Root, which was done during development. There is still no hard value for positioning of the RFQ vane, with respect to a known reference point. It will be critical to find this distance, with accuracy and precision, if the model is to be trusted. Olivier: Rotation by -45deg to accomodate tilted RFQ 4-vane structure. From RFQ vane positioning measured back from MEBT:Q1/endOf_sequence, this places the end of the IRA:Q4 to RFQ start drift position at s = 6729.9224. The twiss parameters at the RFQ entrance (beginning of radial matcher) which produce an ideal match are as follows: (same for x,y - transverse) a = 0.416685 b = 5.229370 call TWISSMATCH( 1, 0.41665, 5.229370, 1., 1) call TWISSMATCH( 3, 0.41665, 5.229370, 1., 1) Olivier: Distance on ISK0141D.DWG from IRA:Q4 midpoint at x = -111.298" y = 2913.729" measured to beginning of MEBT vacuum flange at: x = -111.298" y = 3221.523" (end of sequence point x,y) is dY = 307.794" = 7817.9676mm also note that the above point (-111.298";3221.523") corresponds to the point, on IBP0436D.DWG: x = 217.679" y = 76.798", which is the start of the mebt_db0 sequence. Olivier: Sequence starting point referenced to IBP0436D.DWG at coordinates (inches): x = 217.679" y = 76.798" This corresponds to the start of the vacuum flange on the MEBT side, and agrees with both drawings IBP0436D.DWG and on ISK0141D.DWG to (inches); x = -111.298" y = 3221.523" this ensures the ilt_db33 sequence and mebt_db0 start at a common reference point with no artificial drifts. call TWISSMATCH( 1, -2.35, 98.0, 1., 1) call TWISSMATCH( 3, 0.14, 10.7, 1., 1) Danfysik 1987 L1 - QE-12B - #87115 Danfysik 1987 L1 - QE-7B - #87104 Danfysik 1987 L1 - QE-13A - #87130 Danfysik 1987 L1 - QE-12A - #87135 Danfysik 1987 L1 - QE-13B - #87134 This device does not exist in EPICS at all, it is a foil carousel that is adjusted locally. Olivier: Back-rotate by -45deg around optical axis. At this point, MEBT quads go from being tilted by 45 to being "flat". The bunch rotator is used to create a round beam spot on the stripping foil, in addition to a time focus. Thus, rotating the beam by 45deg (in transoptr) at this location should not result in discontinuities in the envelope. Danfysik 1987 L1 - QE-23 - #87124 Danfysik 1987 L1 - QE-11A - #87118 Olivier: See TRI-DNA-97-03, p. 11-12 for K1 discussion. No word on K2 in that reference however. "Given that the anticipated vertical beam size in the dipole is +-5mm = +-0.20in., we suggest that a value of K1 = 0.55 be used in TRANSPORT calculations." finally, the full gap is noted as (p.1) g = 2.250in. = 0.0572m = 5.72cm Note that these are design parameters, but for now it is the only measured reference. Danfysik 1987 L1 - QE-11B - #87123 Danfysik 1987 L1 - QE-24A - #87122 Danfysik 1987 L1 - - #87125 Danfysik 1987 L1 - - #87112 Danfysik 1987 L1 - - #87129 Danfysik 1987 L1 - - #87120 Olivier: end of mebt db0 marker is measured on DTL tank1 outer surface, on the MEBT:Q13 side. On IBP0500D.DWG, this corresponds to coordinates [inches]: x = 51.9199" y = 71.1069" Olivier: I've changed endOf_mebt_db0 reference to being tank1 outer surface on IBP0500D.DWG. Therefore, it follows that all values referenced in the DTL (this file) are referenced to the same point on IRF1002D.DWG. This places tank1 midpoint s-coordinate at the middle of my DTL Tank1 opera mapping, which is also referenced to tank1 outer surface (on the MEBT:Q13 side). January 29, 2019 IRF1002D.DWG, tank1 start point X=51.1528" tank1 field map (Opera) length = 12.8923" NOTE: Feb 21 2019 - all XY steerers placed 10mm after the central triplet quad as a placeholder for tuneX. NOTE: Sept 13, 2019 (Olivier): see TRI-BN-19-18 for langevin DTL quad fits do not remove factor of 2 multiplying langevin tanh values. The optr attribute scalX is the x-scaling of the pseudoLangevin function defined as the interval over which original magnet surveys were performed. NOTE: Sept 15, 2020 (Spencer) - all diagnostic devices are just temporarily put at positions so as to avoid negative drifts. Position is placeholder to avoid negative drifts. Position is placeholder to avoid negative drifts. Olivier: DTL:XYCB2 placed 10mm after Q2 as a placeholder. IRF1002D.DWG, buncher1 start point X=78.3961" buncher1 field map (Opera) length = 5.1378" Position is placeholder to avoid negative drifts. Position is placeholder to avoid negative drifts. DTL Tank2 referenced to tank2 outer surface on IRF1002D.DWG, corresponding to X=85.4433", consistent with Opera simulation alignment reference. IRF1002D.DWG Tank2 start outer surface X = 85.4433" tank2 field map (Opera) length = 21.5650" Olivier: DTL:XYCB5 placed 10mm after Q5 as a placeholder. IRF1002D.DWG Buncher2 start outer surface X = 121.3338" buncher2 field map (Opera) length = 5.8465" Position is placeholder to avoid negative drifts. Position is placeholder to avoid negative drifts. IRF1002D.DWG Tank3 start outer surface X = 129.0897" tank3 field map (Opera) length = 32.1950" Olivier: DTL:XYCB8 placed 10mm after Q8 as a placeholder. IRF1002D.DWG Buncher3 start outer surface X = 175.6102" buncher3 field map (Opera) length = 6.8307" Position is placeholder to avoid negative drifts. Position is placeholder to avoid negative drifts. IRF1002D.DWG Tank4 start outer surface X = 184.3503" tank4 field map (Opera) length = 37.3130" Olivier: DTL:XYCB11 placed 10mm after Q11 as a placeholder. Position is placeholder to avoid negative drifts. Position is placeholder to avoid negative drifts. IRF1002D.DWG Tank5 start outer surface X = 238.8107" tank5 field map (Opera) length = 40.4630" end of dtl_db0 referenced to Tank5 outer surface on IRF1002D.DWG at X = 279.2737" Olivier: Sequence starts on drawing IHE0281D.DWG at coordinates (milimeters): x = 1403.8054mm y = 11955.7177mm which corresponds to the outer surface of DTL Tank5, also corresponding to the end of sequence for dtl_db0.xml, referenced to drawing IRF1002D.DWG at (inches): x = 279.2737" y = 157.4651" November 24, 2019 Olivier - marker t3d tune starts 65.0cm before Q1 BI relationships based on data collected by D. Evans and analysis by R. Baartman (B-I Curve fits for TRIUMF Quads - TRI-DN-07-04) Danfysik 1987 L1 Danfysik 1987 L1 - QE-9B - #87109 Danfysik 1987 L1 - QE-22C - #87107 HEBT:Q4 DISABLED. Danfysik 1987 L1 - QE-21 - #87127 Danfysik 1987 L1 - QE-19C - #87110 Historical T3D tune 'hebt1-august2012-noQ4.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.2 mm/mrad (20.0 cm/rad) call TWISSMATCH(1, 0., 20.0, 1., 1) call TWISSMATCH(3, 0., 20.0, 1., 1) Olivier: strp5 position at s=3681.7971mm produces a ~5.22cm error with trace3D benchmarking, when sub-sequence from HEBT:Q6 to HEBT:Q10. Adjusted accordingly. Olivier: diag positions for FC5,SCD5 are placeholders to avoid negative drifts. Danfysik 1987 L1 - QE-20A - #87111 Danfysik 1987 L2 - QE-26B - #87147 Danfysik 1987 L1 - QE-20C - #87117 Olivier: XCOL8A actual position is (millimeters); y = 5869.6426mm producing an s value of (mm): s = 6086.0751, which places it within DSB:MB0 - not doable in transoptr, so device was moved back. This device is not used in beam simulations. Olivier: Sequence ends on drawing IHE0281D.DWG at coordinates (millimeters): x = 1403.5516mm y = 6007.5647mm All positions ('s') for optics and diagnostics confirmed using IHE0281D.DWG. Effective lengths to be confirmed. Sequence referenced to drawing IHE0281D.DWG using starting coordinates (millimeters): x = 1403.5516 mm y = 6007.5647 mm which is also the end of sequence hebt_db0.xml BI relationships based on data collected by D. Evans and analysis by R. Baartman (B-I Curve fits for TRIUMF Quads - TRI-DN-07-04) Field maps for DSB Buncher by O. Shelbaya (TRANSOPTR Implementation of ISAC-II - TRI-BN-19-13) Corresponds to T3D file 'sbend January 2014.t3d' Danfysik 2003 L1 - #2139 DSB:IV2 location is approximate. Danfysik 2003 L1 - #2151 DSB:YCB2 location is approximate. Comparing w/ T3D file 'sbend January 2014.t3d', MB2 appeared too close to Q2 by ~ 2mm and too far away from Q3 by ~2mm which suggest a mistake to me. I'm adjusting accordingly and any further checks should double check both the design drawing and T3D. Danfysik 1982 L2 - #82461 Moved tomography reconstruction here for DSB:RPM4. Don't really trust DSB:Q3 at this point. Danfysik 2003 L1 - #2145 DSB:XCB4 location is approximate. DSB:YCB4 location is approximate. Historical T3D tune 'sbend January 2014.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.2 mm/mrad (20.0 cm/rad) call TWISSMATCH(1, 0., 20.0, 1., 1) call TWISSMATCH(3, 0., 20.0, 1., 1) DSB:FC4 location is approximate. Danfysik 2003 L1 - #2154 Danfysik 2003 L1 - #2143 DSB:XCB6 location is approximate. DSB:YCB6 location is approximate. DSB:IV6 location is approximate. Danfysik 2003 L1 - #2144 Danfysik 2003 L1 - #2147 DSB:XCB8 location is approximate. DSB:YCB8 location is approximate. SK - Position of LPM8 doesn't agree w/ marker in T3D SK - Keiko on teams says LPMs do not have waveform records (arrays) What is plotted on EDM page is DSB:FC8:RDCUR vs DSB:LPM8:MOTOR.RBV DSB:LPM8:MOTOR.RBV is digital readback value. DSB:LPM8:RDPOS is analog readback value Location of DSB buncher doesn't agree with the design drawing or T3D. T3D has centre DSB:Q8 to centre DSB buncher of 730 mm IHE0281D has centre DSB:Q8 to centre DSB bunch of 690 mm. Acc currently has centre DSB:Q8 to centre DSB bunch distance of 637.049 mm Centre Q8 to centre Q9 distance is the same for acc/T3D/design, all are 1280 mm OS to investigate why he located DSB bunch here and let SK know. Just chose random point between buncher and DSB:Q9 for tomography reconstruction. Danfysik 2003 L1 - #2157 Danfysik 2003 L1 - #2138 DSB:XCB10 location is approximate. DSB:YCB10 location is approximate. DSB:IV10 location is approximate. Danfysik 2003 L1 - #2153 Danfysik 2003 L1 - #2141 DSB:XCB12 location is approximate. DSB:YCB12 location is approximate. DSB:FC12 location is approximate. Historical T3D tune 'sbend January 2014.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.8 mm/mrad (80.0 cm/rad) call TWISSMATCH(1, 0., 80.0, 1., 1) call TWISSMATCH(3, 0., 80.0, 1., 1) DSB:SCD12 location is approximate. Danfysik 2003 L1 - #2150 Danfysik 2003 L1 - #2155 DSB:YCB14 location is approximate. DSB:IV14 location is approximate. Danfysik 2003 L1 - #2152 DSB:XCOL15 location is approximate. Danfysik 2003 L1 - #2148 DSB:YCB16 location is approximate. SCB:XCB0 location is approximate. SCB:YCB0 location is approximate. Danfysik 2003 L1 - #2149 Danfysik 2003 L1 - #2156 SCB:IV2A location is approximate. SCB:XCB2 location is approximate. SCB:YCB2 location is approximate. SCB:IV2B location is approximate. Sequence ends on drawing IHE0281D.DWG at coordinates (millimeters): x = 20407.7996 mm y = 5544.9802 mm which corresponds to the start of the scb1_db0 sequence, on drawing IHE0467D.DWG (inches): x = 199.81083" y = 436.86151" ** SK - I've moved the end of this sequence 1.4443 mm later so that the distance from SCB:Q2 to SCB1:CAV1 agrees with the T3D value. Further changes should investigate why the drawing and T3D didn't agree. All positions ('s') for optics and diagnostics confirmed using IHE0476D.DWG. Effective lengths to be confirmed. Sequence referenced to drawing IHE0476D.DWG using starting coordinates (inches): x = 199.81083" y = 436.86151" which corresponds to the end of the sequence dsb_db0, on drawing IHE0281D.DWG at coordinates (millimeters): x = 20407.7996 mm y = 5544.9802 mm BI relationships based on data collected by D. Evans and analysis by R. Baartman (B-I Curve fits for TRIUMF Quads - TRI-DN-07-04) Field maps for SC cavities were generated by V. Zvyagintsev using CST Microwave studios. Corresponds to T3D file 'solenoidRFgap8cryo.t3d' Historical T3D tune 'sbend January 2014.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.8 mm/mrad (80.0 cm/rad) call TWISSMATCH(1, 0., 80.0, 1., 1) call TWISSMATCH(3, 0., 80.0, 1., 1) Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits correlation between x, x' and y, y' to 0. call fit(1,2,1,0.,1.,1) call fit(1,4,3,0.,1.,1) Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits correlation between x, x' and y, y' to 0. call fit(1,2,1,0.,1.,1) call fit(1,4,3,0.,1.,1) Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits correlation between x, x' and y, y' to 0. call fit(1,2,1,0.,1.,1) call fit(1,4,3,0.,1.,1) Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits correlation between x, x' and y, y' to 0. call fit(1,2,1,0.,1.,1) call fit(1,4,3,0.,1.,1) Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits correlation between x, x' and y, y' to 0. call fit(1,2,1,0.,1.,1) call fit(1,4,3,0.,1.,1) Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits correlation between x, x' and y, y' to 0. call fit(1,2,1,0.,1.,1) call fit(1,4,3,0.,1.,1) Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits correlation between x, x' and y, y' to 0. call fit(1,2,1,0.,1.,1) call fit(1,4,3,0.,1.,1) Sequence ends at midpoint of SCC3:IV2, which is used as a reference point for the start of the sequence sebt_db8.xml, reference on drawing IHE0486D.dwg at coordinates [INCH]: x = 44.71190", y = 103.97870" All positions ('s') for optics and diagnostics confirmed using IHE0486D.dwg and IHE0487D.dwg. Effective lengths to be confirmed. Sequence referenced to drawing IHE0486D.dwg at coordinates (inches): x = 44.71190" y = 103.97870" which corresponds to the centerpoint of SCC3:IV2 on IHE0486D.dwg. BI relationships based on data collected by D. Evans and analysis by R. Baartman (B-I Curve fits for TRIUMF Quads - TRI-DN-07-04) Corresponds to T3D files 'sebt hb sc.T3D' and 'TIGRESSfinal04-Q22L5.t3d' SCC3:XCB0 location is approximate. SCC3:YCB0 location is approximate. Historical T3D tune 'solenoidRFgap8cryo.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.8 mm/mrad (80.0 cm/rad) call TWISSMATCH(1, 0., 80.0, 1., 1) call TWISSMATCH(3, 0., 80.0, 1., 1) Danfysik 1987 L2 - #87141 Danfysik 1987 L2 - #87142 Danfysik 1987 L2 - #87143 Danfysik 1987 L2 - #87144 Historical T3D tune 'SEBT HB SC.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.8 mm/mrad (80.0 cm/rad) call TWISSMATCH(1, 0., 80.0, 1., 1) call TWISSMATCH(3, 0., 80.0, 1., 1) SEBT:XCB12 and YCB12 are not in IHE0486D.dwg, positions are approximate. Danfysik 1982 L1 - #82444 Danfysik 1982 L1 - #82452 SEBT:XCB14 and YCB14 are not in IHE0486D.dwg, positions are approximate. Danfysik 1982 L1 - #82458 Danfysik 1982 L1 - #82459 Switch reference from IHE0486D.dwg to IHE0487D.dwg, with common reference at centerpoint of SEBT:Q16. New starting reference on IHE0487D.dwg (inches): x = 29.75089" y = 103.9787" centerpoint SEBT:Q16. end coordinates on IHE0486D.dwg are (inches): x = 369.3457", y = 103.97870" Historical T3D tune 'SEBT HB SC.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.8 mm/mrad (80.0 cm/rad) call TWISSMATCH(1, 0., 80.0, 1., 1) call TWISSMATCH(3, 0., 80.0, 1., 1) Danfysik 1987 L2 - #87145 Danfysik 1987 L2 - #87149 Danfysik 1987 L2 - #87150 Danfysik 1987 L2 - #87151 SK check STRP20A on IHE0467D, should be accurate WRT Q20 Historical T3D tune 'SEBT HB SC.t3d' matches to round beam spot here. Below fits alpha_x = alpha_y = 0, beta_x = beta_y = 0.8 mm/mrad (80.0 cm/rad) call TWISSMATCH(1, 0., 80.0, 1., 1) call TWISSMATCH(3, 0., 80.0, 1., 1) Marrco's T3D files disagree on length of Q21. TIGRESSfinal04-Q22L5.t3d has it's length as 330 mm, while IRIS.t3d has it as 325 mm. Danfysik 1987 L2 - #82460 Danfysik 1982 L5 - #82475 Switch reference from IHE0487D.dwg to IHE0571D.dwg, at centerpoint of SEBT:Q22 (common ref. for both). New ref on IHE0571D.dwg is [INCHES]: x = 248.253" y = 144.882" which is centerpoint SEBT:Q22. Sequence ends at centerpoint of SEBT:IV22 on IHE0571D.dwg, which is at coordinates [INCH]: x = 305.390" y = 144.882" All positions ('s') for optics and diagnostics confirmed using IHE0571D. Effective lengths to be confirmed. Sequence starts on drawing IHE0571D.dwg at coordinates [INCH]: x = 305.390", y = 144.882", which is the centerpoint of SEBT:IV22. BI relationships based on data collected by D. Evans and analysis by R. Baartman (B-I Curve fits for TRIUMF Quads - TRI-DN-07-04) Corresponds to T3D files 'IRIS.t3d' Danfysik 1982 L2 - #82462 Danfysik 1982 L2 - #82468 CEM2 does not show in IHE0571D.dwg, added based on visual inspection, location is approximate. Local inspection shows SID2 is a bit further than shown in IHE0571D.dwg, location updated based on visual inspection, location is approximate. Local inspection shows IV2 is much different that IHE0571D.dwg. Updated location updated based on visual inspection, location is approximate. Location updated based on approximate visual inspection. As per M. Alcorta, The IRIS IC windows are 10 mm x 10 mm squares. Local inspection shows IV2 is much different that IHE0571D.dwg. Updated location updated based on visual inspection, location is approximate. Locations below updated based on approximate visual inspection. As per M. Alcorta, This is the collimator that is used for alignment. It can be fully out, or can be inserted to provide a 5, 3, or 2 mm diameter circle on the beam axis. As per M. Alcorta,"the silver foil is where we freeze our H2 or D2 onto. we cool it to 4K and it is always present in the beamline no matter what we do. it has a small aperture just in front of it" Aperture is 5 mm diameter circle Ag foil itself is 4.5 um thickness. As per M. Alcorta, scintillator detector area is a 5 cm by 5 cm square.