November 23, 2019
Olivier - putting in service after finding in incomplete state.
XYCB0 positions are placeholder.
Nov. 25, 2019
Reference: ISK4214D-R99.dwg, with sequence starting at coords [inch]:
x = 53.9771"
y = 401.5641"
Further note - x,y in the above context denotes the coordinates on the
technical drawing. Do note that in IMS, the x/y optical convention is flipped.
Olivier - sequence ends on ISK04214d-R99.dwg at coords [inch]:
x = 32.525"
y = 389.1353"
REFERENCES
Design drawings:
ISK4214D-revI
ISK4219D-rev5
November 23, 2019
Olivier - I'm putting these in a serviceable state after finding them
with much missing information/irregular formatting. Believe M. Stewart
and T. Planche authored previous/initial versions. Putting in service
following discussion with FA.
NOTE - XYCB5 positions are placeholder.
reference drawing ISK4214D-R99.dwg with sequence start at coords [inch]:
x = 32.5250"
y = 389.1353"
which is also the end of sequence itw_tm2.xml
ITW COLLIMATORS SET TO 1" APERTURE DIAMETER, VERIFY.
Olivier - sequence ends at ITW:IV5 centerpoint on ISK4214D-R99.dwg
at coords [inch]:
x = -42.2207"
y = 345.6795"
November 23, 2019
Olivier - putting in service after finding in incomplete state.
need to verify these numbers.
Reference drawing ISK4214D-R99.dwg with sequence starting at coords [inch]:
x = -42.2207"
y = 345.6795"
which is also the end of sequence itw_exit.
Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]:
x = -67.0175"
y = 305.7853"
November 23, 2019
Olivier - putting in service after finding in incomplete state.
need to verify all distances/positions and add reference drawings.
Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]:
x = -67.1075"
y = 305.7853"
which is also the end of sequence ims_mb1.xml.
November 23, 2019
Olivier - putting this into service, found this in an incomplete state.
need to verify all distances.
IMS:YCB8 and M8 positions placeholder.
YSLIT10A and YCB10 also placeholder.
end of sequence also is placeholder.
verify IMS:MB2 parameters.
Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]:
x = -67.0441"
y = 105.6724"
which is also the end of sequence ims_db0.xml
NOTE - IMS:RPM14 position is placeholder, device not on drawing.
Olivier - sequence ends on drawing ISK4214D-R99.dwg at coords [inch]:
x = 90.2426"
y = 40.0662"
all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan
November 23, 2019
Olivier - putting into service, found in incomplete state. need to
verify all parameters, starts/ends of sequences, etc.
also check polarities.
XYCB18 are placeholder.
ATT18 too.
Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]:
x = 90.2426"
y = 40.0662"
which is also the end of sequence ims_db6.xml
Olivier - sequence ends on ISK4241D-R99.dwg at coords [inch]:
x = 224.5389"
y = 82.0097"
all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan
November 23, 2019
Olivier - found in incomplete state, putting into service.
slit dimensions are temporary.
check all dims and devices and positions.
Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]:
x = 224.5389"
y = 82.0097"
which is also the end of sequence ims_db15.xml
Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]:
x = 263.6833"
y = 82.0097"
all s measurements were made from ISK0110C -meagan
November 23, 2019
Olivier - putting these into service, found in incomplete state.
need to verify all distances including start/end of sequence
and physical parameters of optics.
check EOS too, it's BS now.
Sequence starts on drawing ISK4241D-R99.dwg at coords [inch]:
x = 263.6833"
y = 82.0097"
which is also the end of sequence ims_db24.xml
Olivier - FC34 not on ISK4241D-R99.dwg, placeholder
pos'n equal to CEM34 for now.
Olivier - sequence ends just beyond IMS:Q37 on ISK4214D-R99.dwg
at coords [inch]:
x = 369.106"
y = -3.8273"
all s measurements were made from ISK4210D -meagan
unsure if this bender is characterized correctly, as it is a vertical bender
Spencer: sequence starts on ISK4210D.DWG at coordinates:
x = 5399.8853 mm
y = 3714.7334 mm
As measured using e drawings pro on spencer's laptop.
This should be the intersection of the beam axis with the skimmer immediately downstream of XCB7.
Spencer: sequence ends on ISK4403D.DWG at coordinates:
x = 5405.5801 mm
y = 5956.6294 mm
As measured using e drawings pro on spencer's laptop.
This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q12.
Spencer: sequence starts on ISK4403D.DWG at coordinates:
x = 5405.5801 mm
y = 5956.6294 mm
As measured using e drawings pro on spencer's laptop.
This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q12.
Spencer: sequence ends on ISK4403D.DWG at coordinates:
x = 5399.5708 mm
y = 9935.0566 mm
As measured using e drawings pro on spencer's laptop.
This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q20.
all s measurements were made from ISK4210D -meagan
all s measurements were made from ISK4210D -meagan
sequences ends on steerer before ILE:Q5 -meagan
Olivier: June 7 2019
Sequence referenced to drawing ISKD554D-rev1.dwg,
originally implemented by Meagan Stewart (winter 2019
coop student). Sequence starts at coordinates [INCH]:
x = 67.795"
y = 220.048"
Q5-10 lengths changed from eletrical length to effective. See:
http://lin12.triumf.ca/Optics/Quadrupoles/FFintegrals/ISISACsummary.txt
Olivier: Sequence ends on drawing ISK4554D-rev1.dwg at coords [INCH]:
x = 67.795"
y = 277.505"