November 23, 2019 Olivier - putting in service after finding in incomplete state. XYCB0 positions are placeholder. Nov. 25, 2019 Reference: ISK4214D-R99.dwg, with sequence starting at coords [inch]: x = 53.9771" y = 401.5641" Further note - x,y in the above context denotes the coordinates on the technical drawing. Do note that in IMS, the x/y optical convention is flipped. Olivier - sequence ends on ISK04214d-R99.dwg at coords [inch]: x = 32.525" y = 389.1353" REFERENCES Design drawings: ISK4214D-revI ISK4219D-rev5 November 23, 2019 Olivier - I'm putting these in a serviceable state after finding them with much missing information/irregular formatting. Believe M. Stewart and T. Planche authored previous/initial versions. Putting in service following discussion with FA. NOTE - XYCB5 positions are placeholder. reference drawing ISK4214D-R99.dwg with sequence start at coords [inch]: x = 32.5250" y = 389.1353" which is also the end of sequence itw_tm2.xml ITW COLLIMATORS SET TO 1" APERTURE DIAMETER, VERIFY. Olivier - sequence ends at ITW:IV5 centerpoint on ISK4214D-R99.dwg at coords [inch]: x = -42.2207" y = 345.6795" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify these numbers. Reference drawing ISK4214D-R99.dwg with sequence starting at coords [inch]: x = -42.2207" y = 345.6795" which is also the end of sequence itw_exit. Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = -67.0175" y = 305.7853" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify all distances/positions and add reference drawings. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = -67.1075" y = 305.7853" which is also the end of sequence ims_mb1.xml. November 23, 2019 Olivier - putting this into service, found this in an incomplete state. need to verify all distances. IMS:YCB8 and M8 positions placeholder. YSLIT10A and YCB10 also placeholder. end of sequence also is placeholder. verify IMS:MB2 parameters. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = -67.0441" y = 105.6724" which is also the end of sequence ims_db0.xml NOTE - IMS:RPM14 position is placeholder, device not on drawing. Olivier - sequence ends on drawing ISK4214D-R99.dwg at coords [inch]: x = 90.2426" y = 40.0662" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - putting into service, found in incomplete state. need to verify all parameters, starts/ends of sequences, etc. also check polarities. XYCB18 are placeholder. ATT18 too. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = 90.2426" y = 40.0662" which is also the end of sequence ims_db6.xml Olivier - sequence ends on ISK4241D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - found in incomplete state, putting into service. slit dimensions are temporary. check all dims and devices and positions. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" which is also the end of sequence ims_db15.xml Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = 263.6833" y = 82.0097" all s measurements were made from ISK0110C -meagan November 23, 2019 Olivier - putting these into service, found in incomplete state. need to verify all distances including start/end of sequence and physical parameters of optics. check EOS too, it's BS now. Sequence starts on drawing ISK4241D-R99.dwg at coords [inch]: x = 263.6833" y = 82.0097" which is also the end of sequence ims_db24.xml Olivier - FC34 not on ISK4241D-R99.dwg, placeholder pos'n equal to CEM34 for now. Olivier - sequence ends just beyond IMS:Q37 on ISK4214D-R99.dwg at coords [inch]: x = 369.106" y = -3.8273" all s measurements were made from ISK4210D -meagan unsure if this bender is characterized correctly, as it is a vertical bender Spencer: sequence starts on ISK4210D.DWG at coordinates: x = 5399.8853 mm y = 3714.7334 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of XCB7. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 5405.5801 mm y = 5956.6294 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q12. Spencer: sequence starts on ISK4403D.DWG at coordinates: x = 5405.5801 mm y = 5956.6294 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q12. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 5399.5708 mm y = 9935.0566 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q20. all s measurements were made from ISK4210D -meagan all s measurements were made from ISK4210D -meagan sequences ends on steerer before ILE:Q5 -meagan Olivier: June 7 2019 Sequence referenced to drawing ISKD554D-rev1.dwg, originally implemented by Meagan Stewart (winter 2019 coop student). Sequence starts at coordinates [INCH]: x = 67.795" y = 220.048" Q5-10 lengths changed from eletrical length to effective. See: http://lin12.triumf.ca/Optics/Quadrupoles/FFintegrals/ISISACsummary.txt Olivier: Sequence ends on drawing ISK4554D-rev1.dwg at coords [INCH]: x = 67.795" y = 277.505" all s measurements were made from ISK4554D, ILE1095D, and ISK4231D -meagan Olivier, June 7, 2019 Sequence starts on drawing ILE1095D.dwg at coords [INCH]: x = 434.6673" y = 489.8345" starting where ile_db5.xml ends. Quad lengths changed from eletrical length to effective. See: http://lin12.triumf.ca/Optics/Quadrupoles/FFintegrals/ISISACsummary.txt SK - Q11 was replaced by a steering quad in 2020(?). length, aperture, position, need to be confirmed. I've updated PVs to get it working in tuneX. YCB11 is now part of steering quad Q11, position set after to avoid negative drifts. XCB11 is now part of steering quad Q11, position set after to avoid negative drifts. Olivier: Sequence ends on ILE1095D.dwg at coords [INCH]: x = 434.6673" y = 528.1803" all s measurements were made from ISK4231D -meagan Olivier: 7 June 2019, Sequence starts on drawing ISK4231D.dwg at coords [INCH]: x = -455.4295 y = 534.9285 CHECK ILE2:B1 OPTR PROPERTIES Quad lengths changed from eletrical length to effective. See: http://lin12.triumf.ca/Optics/Quadrupoles/FFintegrals/ISISACsummary.txt Olivier: sequence ends on ISK4231D.dwg at coords [INCH]: x = -438.3511" y = 559.3992" Olivier: 7 June 2019, sequence starts on drawing ISK4369D.dwg at coords [inch]: x = -35.79637" y = -7.98761" Quad lengths changed from eletrical length to effective. See: http://lin12.triumf.ca/Optics/Quadrupoles/FFintegrals/ISISACsummary.txt Olivier: Sequence ends on drawing ISK4369D.dwg at coords [INCH]: x = 0.02888" y = 27.92116" REFERENCES Design drawings: ISK4369D-revG sequence begins at end of deflector ILE2T:YCB3 x = 0.02888" y = 27.92116" -meagan Olivier: 7 June 2019 corrected typos, Meagan's references remain in effect. Quad lengths changed from eletrical length to effective. See: http://lin12.triumf.ca/Optics/Quadrupoles/FFintegrals/ISISACsummary.txt sequence ends at end of quad ILE2T:Q3 x = -0.01242" y = 37.53216" -meagan sequence end moved forward from above values by 5.46*mm to allow increased length of Q3 (effective vs electrical). trfc_db1 also moved forward by the same amount. REFERENCES Design drawings: ISK4369D-revG sequence begins at end of quad ILE2T:Q3 x = -0.01242" y = 37.53216" -meagan Sequence moved forward by spencer by 5.46*mm to end at ILE2:Q3 effective end rather than electrical end. All device positions in this sequence adjusted accordingly. copied and pasted epics information from another IV, unsure if the same for this IV or if these values are in epics -meagan beginning of faraday cage/rfq -meagan decel element type, optr tag, and length taken from rick's decel-to-rfq transoptr file, with s value measured from ISK4369D -meagan sequence ends on skimmer TRFC:SK3B after decelerator x = -0.01242" y = 64.81948" total distance from TIS anode: 3473.421mm -meagan REFERENCES Design drawings: ISK4369D-revG sequences includes RFQ for future addition, however for now running tune from TRFC:SK4 which is the skimmer after the RFQ, giving offset of 793.171mm. The coordinates of this starting point on ISK4369D are x = -0.01242" y = 96.10919" sequence begins on TRFC:SK3B on ISK4369D, top blue line of skimmer after decelerator x = -0.01242" y = 64.81948" -meagan no way to model rfq cooler in transoptr yet, put in as a marker to show where it lies on beamline -meagan all simulations should start from here (skimmer at exit of RFQ) -meagan electrode before drift tube, name in progress :) -meagan start point for comparing to rick's asymetrical section transoptr file -meagan start point for comparing to rick's first lens after rfq transoptr file -meagan sequence ends at end of faraday cage enclosing rfq and einsel lens x = -0.01342" y = 121.48306" distance from TRFC:SK4 (total path length) is 645.452mm total distance from TIS anode: 4912.044mm -meagan