November 23, 2019 Olivier - putting in service after finding in incomplete state. XYCB0 positions are placeholder. Nov. 25, 2019 Reference: ISK4214D-R99.dwg, with sequence starting at coords [inch]: x = 53.9771" y = 401.5641" Further note - x,y in the above context denotes the coordinates on the technical drawing. Do note that in IMS, the x/y optical convention is flipped. Olivier - sequence ends on ISK04214d-R99.dwg at coords [inch]: x = 32.525" y = 389.1353" REFERENCES Design drawings: ISK4214D-revI ISK4219D-rev5 November 23, 2019 Olivier - I'm putting these in a serviceable state after finding them with much missing information/irregular formatting. Believe M. Stewart and T. Planche authored previous/initial versions. Putting in service following discussion with FA. NOTE - XYCB5 positions are placeholder. reference drawing ISK4214D-R99.dwg with sequence start at coords [inch]: x = 32.5250" y = 389.1353" which is also the end of sequence itw_tm2.xml ITW COLLIMATORS SET TO 1" APERTURE DIAMETER, VERIFY. Olivier - sequence ends at ITW:IV5 centerpoint on ISK4214D-R99.dwg at coords [inch]: x = -42.2207" y = 345.6795" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify these numbers. Reference drawing ISK4214D-R99.dwg with sequence starting at coords [inch]: x = -42.2207" y = 345.6795" which is also the end of sequence itw_exit. Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = -67.0175" y = 305.7853" November 23, 2019 Olivier - putting in service after finding in incomplete state. need to verify all distances/positions and add reference drawings. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = -67.1075" y = 305.7853" which is also the end of sequence ims_mb1.xml. November 23, 2019 Olivier - putting this into service, found this in an incomplete state. need to verify all distances. IMS:YCB8 and M8 positions placeholder. YSLIT10A and YCB10 also placeholder. end of sequence also is placeholder. verify IMS:MB2 parameters. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = -67.0441" y = 105.6724" which is also the end of sequence ims_db0.xml NOTE - IMS:RPM14 position is placeholder, device not on drawing. Olivier - sequence ends on drawing ISK4214D-R99.dwg at coords [inch]: x = 90.2426" y = 40.0662" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - putting into service, found in incomplete state. need to verify all parameters, starts/ends of sequences, etc. also check polarities. XYCB18 are placeholder. ATT18 too. Sequence starts on drawing ISK4214D-R99.dwg at coordinates [inch]: x = 90.2426" y = 40.0662" which is also the end of sequence ims_db6.xml Olivier - sequence ends on ISK4241D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" all s measurements were made from ISK0110C, though unsure if this drawing is completely accurate at this section -meagan November 23, 2019 Olivier - found in incomplete state, putting into service. slit dimensions are temporary. check all dims and devices and positions. Sequence starts on drawing ISK4214D-R99.dwg at coords [inch]: x = 224.5389" y = 82.0097" which is also the end of sequence ims_db15.xml Olivier - sequence ends on ISK4214D-R99.dwg at coords [inch]: x = 263.6833" y = 82.0097" all s measurements were made from ISK0110C -meagan November 23, 2019 Olivier - putting these into service, found in incomplete state. need to verify all distances including start/end of sequence and physical parameters of optics. check EOS too, it's BS now. Sequence starts on drawing ISK4241D-R99.dwg at coords [inch]: x = 263.6833" y = 82.0097" which is also the end of sequence ims_db24.xml Olivier - FC34 not on ISK4241D-R99.dwg, placeholder pos'n equal to CEM34 for now. Olivier - sequence ends just beyond IMS:Q37 on ISK4214D-R99.dwg at coords [inch]: x = 369.106" y = -3.8273" all s measurements were made from ISK4210D -meagan unsure if this bender is characterized correctly, as it is a vertical bender Spencer: sequence starts on ISK4210D.DWG at coordinates: x = 5399.8853 mm y = 3714.7334 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of XCB7. Spencer: sequence ends on ISK4403D.DWG at coordinates: x = 5405.5801 mm y = 5956.6294 mm As measured using e drawings pro on spencer's laptop. This should be the intersection of the beam axis with the skimmer immediately downstream of ILT:Q12.